Truck Tires Accidents Caused By Defective Equipment

Truck Tire Blowouts

It is important to use the utmost caution when making your way through traffic, especially if you are driving near an 18-wheeler. If an 18-wheeler’s tire blows out, serious accidents can occur, and in some instances, truck tire blowout accidents can be deadly. Sadly, many tire truck blowout accidents could be prevented by trucking companies and drivers acting safely and ensuring that their trucks are safe to drive.

If you or your loved one was injured in an 18-wheeler tire blowout accident, contact a Des Moines truck accident lawyer at LaMarca Law Group, P.C. Our experienced attorneys are ready to help you understand your legal rights and options in this situation, so contact us today by calling (515) 225-2600.

Causes of Truck Tire Blowouts

The following are the three most common causes of 18-wheeler tire blowout accidents:

  • Tire recaps – In order to save money, truck drivers may try to repair tires instead of replacing them.
  • High mileage – Truck companies are responsible for ensuring that worn down tires are replaced.
  • Mismatched tires – Failure to ensure that the right type and size of tire is put on an 18-wheeler can cause a blowout.

Why Are Tire Blowouts Dangerous?

The most obvious reason is that it creates instability in the vehicle. Though truck drivers are trained how to recover from a tire blowout, the impact of tire blowouts is often unpredictable. A perfectly trained driver can still easily lose control of his vehicle after a vehicle. The second reason truck blowouts are so dangerous is because they’re typically unexpected and abrupt. Many driving hazards can be identified prior to the hazard being a huge safety risk.

For example, if a truck driver is driving defensively, he may notice that traffic has halted to a stop ahead. This early identification of the hazard allows the driver to began to brake with plenty of time to stop. On the other hand, most blowups aren’t predictable. Therefore, a driver will be driving along the roadway when “BOOM!” The driver has been thrust into an immediate perilous situation and must adapt on the fly.

Here are 4 of the most common causes of truck tire blowouts:

1. Improper Maintenance

An overinflated tire can cause the tread to wear down fast in the center of the tire whereas an under-inflated tire causes the tread to wear down quickly on the sides.  Both reduce the lifespan of the tire considerably faster than if the tire was inflated properly.  Either air imbalance makes the tire more susceptible to blowouts.  It is important to have tires properly inflated. 

2. Overloaded Trailer

An overloaded trailer can cause excessive wear and tear on tires and brakes, causing them to fail without warning.  A loaded trailer can weigh up to 80,000 pounds, and so it is crucial to have properly inflated tires that have minimal wear and good treads.

3. Roadway Hazards

If a tire were to hit a pothole or some roadway debris, the integrity of the tire would be damaged.  The impact between the tire and the roadway hazard can cause the tire’s internals to be pinched, and, if hit hard enough, the rubber and fabric to be cut through completely.

4. Unnoticed Small Tire Leaks

Sometimes, a seemingly small tire leak can lead to a dangerous blowout. The slow release of air slowly weakens the tire until it inevitably and suddenly fails.

Although preventing tire blowouts is not always possible, the chances of them occurring can be reduced if tire maintenance is up kept. Checking on tire conditions often makes it more likely problems could be caught early. It is important for every truck driver to include a detailed review of the truck’s tire conditions as part of the pre-trip inspection.

Signs of Your Tires Need Repair / Replacement:

  • Low Tire Tread – Tire tread is incredibly important when it comes to the safety of your truck. The little grooves help provide traction for your vehicle and prevents unnecessary slipping and sliding. If you have low tire tread, often from wear, it’s important to get the tires replaced.
  • Tire Warning Light – Of course, if you see the tire warning light, it means something is wrong with your tire. Usually when this light turns on, it means you have low tire pressure. While most vehicles are fixed with adding more air, some cases prove more complicated. Low tire pressure can indicate larger issues.
  • Cracked Tires – Cracks in tires are definitely a sign that your tire needs repair or replacement. Cracks in tires can indicate tire leaks or signal a future blowout. These should be checked immediately to prevent serious accidents or other dangers.
  • Tire Vibration – Cars naturally vibrate when they are in motion. If your car is vibrating more than usual or it just feels “off,” it’s time to get your vehicle professionally checked. Tire vibrations can mean problems with your alignment, damaged suspension, and more.

Tire Repair Vs. Tire Replacement – What To Know

Not all mishaps to tires can be repaired. Whether or not you can repair your tire depends on the type of tire and what exactly happened to the tire. Read below to find out if your tire can be fixed or needs to be replaced.

1. A sidewall puncture needs to be replaced – Even if we can patch it up, the patch will come loose after enough time. Weaknesses in the sidewall will face incredible amounts of pressure so this tire needs to be replaced.

2. A shoulder puncture cannot be repaired – The shoulder of the tire connects the side of the tire with the flat portion, and punctures here face the most pressure, so any patch or plug will come undone under the extreme forces of the road.

3. A tire that has been driven on while flat or low air pressure – If you’ve driven on your questionable tire at all, then it’s very unlikely that you’ll be able to get it fixed. Still, try visiting our Santa Clarita tire repair specialists, but the chances are you’ve caused damage beyond repair.

4. A puncture on the flat part of the tire that’s less than 1/4″ in diameter – These punctures can be fixed so long as they’re not within 2 inches of the shoulder.

Bathroom Remodeling Tips

The Ultimate Guide to Bathroom Sinks: Which Type Is Right for You?

There are many styles of bathroom sinks, and each has its particular pros and cons—including its price. Since this seemingly simple fixture can have such a big impact on how a bathroom functions and looks, you may be wondering: What’s the best basin for our home?

That depends, of course, on your sense of style, budget, how many toiletries you like to stash on your counter, and plenty of other factors. “There are a large number of sinks that can be used in the bathroom, and in many cases, it’s just a question of aesthetics,”

Pedestal sinks

A pedestal sink consists of a wall-hung basin with a pedestal that covers the plumbing.

Cost: $50 to $600

Pros: This is the most common type of bathroom sink, which means that they are easy to find

Cons: Pedestal sinks have a small lip, which limits the room you have for setting out things like soap or toothbrush holders

Wall-mount sinks

Wall-mount sinks feature a basin that is hung from the wall at a location and height that you choose. The pipes are partially concealed behind the wall.

Cost: Sinks start at around $60 (the model below is $75 from American Standard and available at Home Depot) and can go up to $700 or so.

Pros: These can be very small or fairly large. And they are good from the standpoint of those who want to take into account universal design or to age in place, because a wheelchair can roll under them, says Walsh.

Cons: Wall-mount sinks have a flat horizontal steel hanger bracket that’s bolted to the wall with the sink fixture hung on the bracket. Because of this design, a gap can open between the sink and the wall if not installed correctly. “And you won’t have a lot of storage or counter space,”

Countertop sinks

These sinks, also called drop-ins and self-rimming sinks, fit into a variety of countertops. Thanks to their self-rimming nature, they’re the simplest type to install. “Countertop sinks are the style most commonly found in high-traffic family bathrooms,”

Cost: Starts at $100 and can go up to $1,000.

Pros: These come in a variety of materials from slumped glass to cultured marble. They are also easy to clean and install because it’s all one component.

Cons: If the sink doesn’t come with an overflow drain, it will end up requiring a grid drain (one that can’t close) in some states.

What’s the Best Bathtub or Shower for Your Bathroom Remodel? How to Pick

One of the most exciting phases of a bathroom remodel is picking out the perfect bathtub or shower. Choosing the right wet features for a bathroom warrants a hard look at all your options. After all, this is how you can turn a necessary room into a spalike retreat

But you probably already know that you have a lot of options to consider—and that it risks getting just a tad overwhelming in addition to figuring out your budget. That’s why, in this latest installment of our “Dream Bathroom Remodeling Guide,” we take you through the best ways to choose a bath, shower, and other wet features for your new bathroom.

Main wet feature considerations

Budget: Before you get your heart set on that Japanese wooden soaking tub, confirm how much cash you have on hand. Generally, you should expect to allocate between 10% and 15% of your total bathroom renovation budget to wet features. Just remember, you can’t take wet features with you when you move, so proceed with caution.

Space: How much space do you have, and what’s your ability to manipulate that space via plumbing? “If you currently only have a walk-in shower but you want a tub, square one is figuring out if you have room to add it,”

Bathing habits: Some people like the look of a walk-in shower, but really love a good soak in the tub. “Alternately, some people haven’t used the tub since their kids were little,”

The Ultimate Guide to Choosing the Best Bathroom Tile for Your Walls, Floors, and More

Types of tile: Pros, cons, and price

Let’s talk about tile choices. “The first thing you need to understand is that all bathroom tile is going to get wet, due to moisture and water vapor,”

That means that every single piece of tile in the entire bathroom—yes, even walls far from a shower or sink—should be able to withstand water. So you want a nonporous tile in the bathroom whenever possible. Porcelain, ceramic, and glass tiles are nonporous and hold up well; meanwhile, marble and many natural stones are porous and should be avoided.

Porcelain tile

Cost: About $2 to $15 per square foot.

Pros: This low-maintenance tile is ideal for both bathroom floors and walls, because the surface absorbs little moisture. That means it also resists stains. In addition, only soap and water are needed to maintain it.

Cons: The one big downside of porcelain is that it’s a pain to install. The material is very dense, which makes precise cuts harder and means that the installation takes longer to complete. This type of tile also requires a fair amount of grout, which can easily get dirty if it isn’t sealed properly.

Ceramic tile

Cost: About $3 to $30 per square foot.

Pros: Ceramic tile not only comes in classic white subway tile but offers a range of colors and patterns that give remodelers a lot of possibilities to choose from. It is exceptionally durable, and examples of ceramic tile have survived intact for thousands of years. It is often used on shower walls.

Cons: Ceramic is softer than porcelain, so it’s not a good option for high-traffic bathroom floors. And when ceramic chips, the color underneath is different from the shade on top, which makes the breakage more noticeable (porcelain is the same color throughout). The tile is also not as water-resistant as porcelain.

Stone

Cost: $1 to $18 per square foot.

Pros: The biggest advantage of stone tiles is their uniqueness and beauty. These eco-friendly tiles are also not as slippery as porcelain and ceramic tile, and their durability makes them a good choice for showers.

Cons: Acid like vinegar can stain or damage natural stone, so you have to be very careful when cleaning it. And because the stone occurs naturally rather than being fired in a kiln, it can have small natural cracks that get larger over time. Just make sure to seal the tile to make it water-resistant. “Never use natural stone in a steam shower, and try to keep green marbles out of the bathroom, as they have a tendency to get flaky around water,”

Crucial Plumbing Facts That Could Make or Break Your Bathroom Remodel

Planning to remodel your bathroom into the oasis of your dreams? Then you’d better get a handle on your plumbing. Even if you don’t see the pipes connected to your sink or shower, understanding how they work is essential if you want your bathroom renovation to turn out all right (and within budget).

Bathroom remodel 101: Types of pipes

In the past, most bathroom plumbing pipes were made of cast iron or galvanized metal. However, these pipes won’t work with many of the newfangled, water-saving setups like, say, low-flow toilets. Low-flow toilets will save about 17,000 gallons of water yearly. (Note: Flushing a standard toilet uses about 38% of an average household’s water.) The catch is, they require PVC (polyvinyl chloride) or PEX (cross-linked polyethylene) pipes. But updating to these kinds of pipes is both easy and affordable.

You also need to figure out if you prefer hidden or exposed plumbing when you’re looking to buy your sink, tub, or toilet.

If you have a lot of visible plumbing, you might want to use copper pipes instead of PVC or PEX, because copper is more appealing aesthetically. Just keep in mind that it’s more expensive and difficult to work with, since sawing and fitting these pipes into place will take more work than cutting soft, flexible PEX/PVC.

Plumbing can affect a bathroom’s layout

The existing water and drain lines in your bathroom usually dictate the location of fixtures in your renovation. You can move pipes and drains—although it’ll cost you—but some relocations might be impossible.

How to Hire a Bathroom Contractor Who’ll Design a Dream, Not a Nightmare

Is it time to turn your en suite bathroom into a personal oasis? Before you start poring over which tiles or slipper tub to install, know that the far more crucial choice is to find the right contractor for the job.

How to find a good bathroom contractor

Sure, ask your friends and neighbors who’ve redone their bathroom for recommendations. But that should just be the start. You’ll want to go online to conduct a broad search for contractors in your area, particularly those who specialize in bathrooms. While any contractor can technically work in any room of the home, it’s best to hire someone with specific bathroom experience. Sometimes it’s essential.

If you are only replacing fixtures that you can pick out, look for a contractor who can simply execute your plans, which will save you money. If you want a complete reimagination, then consider hiring a contractor who can also help you with design.

Questions to ask a bathroom contractor

To get a snapshot of the contractor’s business practices, interview all your potential hires before a meeting. Ask if they have experience with bathrooms similar to yours. Because if you have an older home with tricky plumbing, you likely want a contractor who can roll with quirks. Ditto if you live in a brand-new condo with high-pressure plumbing.

Finally, ask how often the contractor will communicate with you. If he has a lot of other projects that keeps him away, who will realize if, for example, the wrong cabinets were delivered? That may seem like a small thing, but there’s a six-week lead time for cabinets, so mistakes can have a massive impact.

The Remote Viewing Electronic Leak Detection

Common Causes of Water Leaks

Water leaks can cause extreme damage to your home. Some of the most common causes for leaks include:

SHIFTING PIPES – If your home is settling, or if your area has recently experienced an earthquake, you may be more prone to water leaks. As your pipes shift they can break and deteriorate, causing ruptures or leaks.

CLOGGED DRAINS – One of the most common causes for water leaks are clogged drains. Clogged drains are caused by the buildup of grease, oil, food and other sediment. Non water-soluble items such as diaper and excess amount of paper towel can also cause clogs.

ROOT SYSTEMS TAKING HOLD – Roots have the ability to break through your pipes into your water system. These types of leaks are often more difficult to fix and notice.

Methods of Detection

methods to detect water leaks in your home. The methods are:

METER DETECTION – As one of the less invasive methods, we are able to test the water pressure in your pipes and compare it to a healthy pipe. This allows us to determine if there is a leak, and where the leak is located.

INFRARED TECHNOLOGY – This is the most modern method of leak detection. It involves using an infrared camera to take pictures of the pipes at different angles to detect the clog.

DIG AND DRILL – This method is the most invasive option, but is still quite effective. It involves digging into your pipes or walls to detect the leak.

Tips and Prevention

Try some of these tips to prevent any future water leaks from occurring:

Insulate pipes that could be exposed to cold temperatures.

Remove outside hoses during colder months.

Keep your pipes in good condition by not using them for alternative reasons, such as a place to hang your clothes.

Inspect your pipes often for small leaks and get them repaired immediately.

Leak Detection and Repair

Helping You Stop Hidden Water Leaks

When you are invested in taking care of your home or commercial space and making sure that everything stays in good order, you are likely most concerned about the things that you can see. You may know how to take care of drips and standing water, but what happens when the problem is not only beneath you but also encased in cement? A slab leak is an example of just such a scenario.

What Is a Slab Leak?

A slab leak is essentially a leak that occurs inside the concrete building slab that is the foundation of your home. This type of leak is fairly common. Sewer, water, and gas pipes run underneath every home, and these metal pipes are prone to corrosion. Tiny pinholes can cause nearly undetectable leaks while a settling foundation, soil movement, or even an earthquake can trigger a leaking pipe. Any home over 25 years old is especially susceptible. In any case, this is something that needs immediate attention from a professional.

Signs that You May Have Slab Leaks

Slab leaks manifest themselves with water pushing up through the floor in your home or through the ground near the home’s concrete slab outside. However, they can go undetected for quite some time, delaying critical basement leak repair. Depending on the location of the leaking pipe, the water might not show up for weeks or months after it starts.

You won’t find a slab leak unless you look for it, but there are warning signs to look for, which include:

Moisture or pooling on your carpets, flooring, or yard

Very high water bill, which indicates water loss

Frequent stoppage or backup of toilets, tubs, and showers

Cracks in your foundation

Mold and mildew growth

Warm areas on the floor

Sudden loss of water pressure

Hearing hissing or running water

Unexplainably damp areas

Do You Suspect a Hidden Leak in Your Home?

There are various methods of slab leak repair, but rest assured will find the right one for you. work is fully guaranteed, and know how important it is for you to have your home in working order. Too many plumbing services will waste your time and money.

Leak Detection

Plumbing leaks can be devastating. Leaks can cause everything from damage to your home’s structure to buckling in your foundation to mold growth in places that you can’t see or get to. When it comes to finding leaks

Even small plumbing leaks can result in severe consequences, but thankfully, it’s possible to outsmart hidden leaks and find them before they can really wreak havoc on your home.

Do You Have a Plumbing Leak?

can come directly to your home and perform a thorough plumbing inspection to determine the location of any leaks you may have. However, how can you tell that you might have a leak that needs to be professionally addressed? There are a few things that you can look out for to help you discover a leak on your own.

You May Be Experiencing A Leak If:

You notice cracks in your walls or your floors

Certain areas of your floor are hot

You can hear the sound of water running when none of your water fixtures are on

Mildew or excessive moisture appears under your carpets

Steps You Can Take to Prevent Further Damage

If you notice a leak, there are a few measures you should take while you wait for our leak detection and plumbing repair team to arrive. First, locate your master water supply, usually located in your garage or somewhere near the front of your home, and shut it off by turning it clockwise. This prevents further damage to your property and stops water waste.

What Is a Slab Leak?

Possibly the most damaging type of leak is one that develops in your home or business’ foundation, commonly referred to as a “slab leak.” Slab leaks can develop over time as buildings settle and shift on their foundations, placing pressure on plumbing lines running through the concrete slabs. If left undetected and unrepaired, a slab leak can cause significant structural damage and even cause a building’s foundation to crumble. As such, it is imperative to catch a slab leak early on to protect your property from potentially catastrophic damage.

Leak detection

What is a leak detection system?

CPLD detection systems are used to determine if and where a leak has occurred. Using hydrostatic testing, infrared and laser technology, Ground Penetrating Radar (GPR), video pipe crawling and concrete scanning, if there’s a line break, leak detection systems will find it.

As a full service plumbing, advanced leak detection specialists and slab leak repair company, CPLD is with you every step of the way. From the moment start to assess your water leak, through working with your insurance company, to cleaning up the water damage, will be there.

What are the types of leak detection?

Simply put, a leak is any opening in a closed system. Air Conditioning systems, water pipe systems, sprinklers are all closed systems. When a break occurs damage can be substantial. With the latest technology and equipment, CPL Detection specializes in finding those leaks before they cause more damage.

Video Camera Pipe Inspection

CPLD uses video camera equipment to successfully detect in-line drain and sewer problems. This is often an infrared camera placed into a line at a toilet drain, existing cleanout or roof vent. Using a video camera pipe inspection, they can identify a small problem so it can be corrected before sewer repair services are necessary.

Ground Penetrating Radar (GPR)

Ground Penetrating Radar (GPR) is a method that uses radar pulse to figure out the subsurface.  This non-destructive method uses high frequency electromagnetic waves detected by radar. Unlike other locators, ground penetrating radar can display images in real time of exact locating and depth of up to 12 feet.  This determines any electrical conduits, rebar pattern and its quality, post-tensioned cables, measure slab thickness, width and depth of voids, PVC conduits, and cooling/heating lines. radar equipment that allows CPLD to locate buried objects easily.

Water Leak Detection

Wasted Water. Wasted Money.

Sometimes we don’t take water leaks very seriously. A faucet is dripping? “It can wait.” A few drops around your water heater?  “Probably nothing.” Well, all water leaks are “something” and bound to become bigger somethings unless taken care of right away.

do much more than repair or replace leaking pipes. related services include:

Electronic water leak detection so we can locate unseen water leaks…these tend to cause the most damage as they can go undetected for quite some time

Slab leak detection…if you have a carpet over a concrete slab and the carpet has a wet spot or feels wet to the touch, no doubt you have a slab leak

Sewer and drain camera detection…using state-of-the-art cameras, can locate the source and extent of drain clog or leak, both above and below ground

Water Leak Inspection | Electronic Leak Detection

investment in cutting edge technology helps save you money. That’s right: faster and more accurate detection saves time, money, and prevents unnecessary digging. Plus, early detection and repair means less damage to walls, ceilings, valuable possessions and more.

Finally, let’s not forget how much water you can save through early detection and repair. Consider the following. If your faucet dripped once every second every day, all day, it would take only four and a half hours to reach one gallon

The Advantages Of A Flat Roof Extension For Your Home

How often should a flat roof be coated?

Even more so than other roofs, flat roofs require maintenance in order to last. This maintenance typically comes in the form of coating the flat roof. A lifespan of an un-coated flat roof is around 10 years but coating it every five years or so can extend this enormously. Coating a flat roof can also save money on costly repairs down the line. How often you need to coat your roof, and which coating is the best, depends on a few factors.

How Can You Tell Your Flat Roof Needs Coating?

Flat roofs are not usually actually flat, but instead have a very slight slope. Because of this, the main issue which affects flat roofs is drainage issues. It’s far better to coat the roof as a pre-emptive measure rather than wait for drainage issues such as ponding or leaks and then attempt to correct them. Ponding can also lead to fine cracks in PVC called crazing. Any signs of structural damage are a sure sign your roof needs coating. However, even if you do not have signs of damage and it has been five or more years since your roof was last coated, it’s still worth coating your flat roof.

How to coat your flat roof

The first step towards coating your roof is to thoroughly clean it. There is no way to ensure a coating properly adheres unless your roof is thoroughly clean.

It can also be a good idea to use a primer on your roof before painting. Primers will help coating thoroughly adhere. Conversely to what you may think, coatings tend to adhere better to rougher surfaces. Check with your coating manufacturer for primer recommendations.

You can paint on your silver coat roof seal yourself. However, if there are underlying issues such a leaks or ponding, it may be better to use a contractor for a more thorough job. If you do undertake the task, remember to take adequate safety precautions. Make sure your ladders are stable and in good condition, and never work in adverse weather conditions.

The Lifespan of a Flat Roof

A flat roof left unmaintained will typically last about 10 years. It’s a good idea to plan for a new coating every five years to ensure its integrity and continued performance. If your flat roof is less than five years old but you’ve noticed the presence of cracks or pooling water, then you’ll want to go ahead and have it coated. Those cracks and pooling water can lead to more extensive damage, the repairs of which may cost far more than a new coating. And, if your flat roof is more than a decade old, even if there are no cracks or pooling water, do your house or commercial building a favor and have it coated.

How to Find Out if Flat Roof Needs Coating

It is important to know that a flat roof is not flat. The term is common due to the slight slope in the roof structure. This is one reason why flat roofs soften face drainage issues.  That is why many roofing experts advise coating your roofs as a preventive measure to keep drainage problems such as leaks at bay instead of correcting them.

Know that severe leaks may lead to cracks in the roof, commonly called crazing.  If your roof shows structural damages, it is an indication that it needs coating.  Even if your roof does not show signs of physical damage but has been more than six years since its last coating, it is worth coating it.

When to Coat a Flat Roof

The main reason to recoat a flat roof is for water protection. If ponding does occur, the roof can leak and cause more damage inside. It’s worth resealing the roof every five years or so to avoid water damage. However, the following factors may often influence the frequency of roof coating:

Roof Style

For flat roofs, regular roof sealing is absolutely crucial since they are at high risk of ponding. So, the surface has to be perfectly waterproof to prevent leakage of water into your building. Even the smallest of leaks should be dealt with promptly to prevent any water damage. Typically, a flat roof left unsealed can have its lifespan reduced by up to 50 percent. Sloped roofs, on the other hand, do not need sealing as often since water can run off more efficiently and is less likely to pool.

Introduction To Drywall Repairs Materials

THINGS YOU SHOULD PAINT INSTEAD OF REPLACE TO SAVE MONEY

You know a fresh coat of paint can give any room a quick and inexpensive facelift. But did you know that a little paint can also perk up carpets, appliances, and even vinyl floors? Basically, if it doesn’t move, you can paint it. But only after you’ve paid special attention to prep — cleaning, patching, and sanding (generally) the area.

Painting isn’t brain surgery, but it’s not a breeze, either. Here are some rules of thumb:

Prime before painting. Primer will allow the paint to adhere better.

Most hard surfaces will take primer better if they’re roughed up a little with fine-grade sandpaper.

When using spray paint, multiple, thin layers are better than one, thick coat. Ease up on your trigger finger, and spray in short bursts.

Wait for the previous coat of paint or primer to dry completely before adding another coat.

Door, Drawer, and Cabinet Hardware

Spray paint can turn builder-grade brass locks and hinges into fashion-forward hardware with an oil-rubbed bronze, pewter, or stainless look.

Prep:

Clean hardware with a fine steel wool to remove grease and grime.

Rough up the surface with fine-grain sandpaper.

Before you paint, insert a tiny strip of painter’s tape into the keyhole to make sure paint doesn’t gunk it up.

Prime with a metallic primer, then paint with metallic spray paint.

Tip:

Insert the door lock’s spindle into a square of Styrofoam, which will hold it upright while you spray around the knob.

Brick Fireplace

When you paint your red brick fireplace, you transform the entire room. But beware! Once you paint brick, it’s nearly impossible to return it to the original brick color. You can paint brick a single color, or achieve some variation — like the variations in real brick — by sponging on slightly lighter and darker hues.

Prep:

Lightly sand away any loose bits of brick or mortar with 120-grit sandpaper.

Clean dirt and soot with a wire brush and heavy-duty cleanser.

Allow to dry completely before applying an oil-based, stain-blocking primer.

Paint with a semigloss latex.

Tips:

Never paint the firebox.

Brick is porous and drinks paint, so buy twice what you think you’ll need.

Wear safety glasses and gloves when cleaning anything with a metal brush.

Ceramic Tile

Imagine how sweet it is to update ceramic tile without having to bust up and cart away tons of old tile. Play it safe and avoid painting tiles in high-traffic and high-moisture areas. Some good places are laundry room floors, backsplashes under cabinets (but not above ranges where pasta sauce splatters), and walls around tubs you rarely use.

Prep:

Repair cracked or chipped tile with caulk or grout before painting.

Give patching material ample time to dry, then lightly sand before applying an epoxy or urethane bonding primer.

Sand after priming and between each coat of quality latex paint.

Wait several days for the paint to cure completely, then seal with two or three coats of clear, water-based polyurethane.

Tips:

To get a smooth look, apply paint in zigzags, then roll down in one, smooth motion.

Use 240-grit wet/dry sandpaper for prep and between coats.

Don’t forget safety goggles and masks when sanding tiles.

Drywall Paper Repair Tips

The brown paper is the inner core of the layered paper that surrounds the gypsum core of common drywall. If you coat this paper now with joint compound you WILL GET BLISTERS. The torn paper area of the drywall has been trimmed and it’s ready to be coated with a sealer (see below) and then repaired.

was removing an ugly ceramic tile backsplash in my kitchen. Some of the drywall paper came off with the old glue. It looks horrible. A home center employee told me I have to put in new drywall. This can’t be true. Is there a way to repair this so the wall is once again perfectly smooth? Surely you know secret ninja tricks that will save me

never forget the first time that happened to me. I was removing large sheets of thin wood paneling that had been nailed and glued over unpainted drywall. Oh my goodness, what a mess I had. The second time it happened to me, I was stripping off wallpaper in a bathroom. The paper hanger didn’t prime the drywall with the proper sealant to prevent the wallpaper glue from bonding to the drywall paper.

First, the advice you received from the home center employee is completely wrong. You don’t have to replace the drywall. I’m going to describe to you how to repair it. It’s a shame that so much bad advice is dispensed each day inside those big box stores.

High-Tech Paper

The common drywall that’s found in many homes is made with high-technology paper. You’d be surprised how thick the actual paper is. You can see it if you look closely at a cross section of drywall after it’s been cut or at the end of a piece before it’s installed.

Things to Know When Painting Your Home Exterior

The exterior of your home is very important, but can be quite challenging to maintain. Before guests and potential homeowners step into a home, it is often times the first aspect they see.

Quality Over Cost

Purchasing better quality exterior paint will save you the labor of painting more than once or twice throughout the year. Along with saving your time and energy, better quality paints are readily available, allowing for paint color to last longer. Working with a professional exterior painter will give you access to a number of recommended paint brands at a cost that suits your budget best.

Mother Nature Is Your Indicator

Planning ahead is beneficial in life, especially when you are planning to paint your home’s exterior. Not only is it the first aspect that guests see, but it is also one of the elements in  your home that is exposed to the outside world. As you plan to paint, check out your local weather patterns. It is better to paint in the dry times of the year so that your paint has time to dry properly.

Check The Health Of Your Siding

Before you start painting, inspect your siding’s current condition. You do not want to paint on siding that‘s already worn down, as it poses as a hazard and may fall off sooner rather than later. Replacing the siding with new components and painting it afterwards will ensure it withstands the elements for a longer period of time.

Prep The Space Around You

Don’t forget to prep the space around you! Painting can be very messy sometimes and may splash onto the area around you if it’s not properly covered and weighed down.

Drywall: Drywall Repair & Painting

If you paint the wall, you own the wall. That’s the prevailing attitude of general contractors and customers when a painting contractor tackles a job. Contrary to their beliefs, however, you know that paint can’t cover up poor drywall work. If you’re faced with an iffy proposition, do you know what to do?

Who’s responsible for the drywall? does a lot of work in new construction settings, both commercial and residential. In this arena, there is typically a separation of responsibilities: The drywallers are responsible for their work and the painting contractor is responsible for painting. Still, based on his prior experience

“I’ll take a visual look and if I see there are some areas that need to be addressed — joints not feathered well or raised spots — and I’ll point them out to the general contractor. Someone has to address those before I start painting.”

Some painting contractors may not want to cause a fuss, fearful of possibly losing future work. What you may not realize is that some of this may already be addressed in a job’s specifications. “A lot of painters don’t read the specs very well — somewhere there are specs on painting and drywall,”

suggests that painting contractors can use two established guidelines to help them in assessing drywall surfaces before they paint them: the drywall finishing standards based on GA-214-96 in the Gypsum Construction Handbook and PDCA Industry Standard P4-04, which addresses responsibility for inspection and acceptance of surfaces prior to painting and decorating.

Common Causes For Drywall Repairs

Just like how we have to go to the doctor every once in a while, our houses also have to go under repair every so often. From small touch ups to large scale renovations, there are a slew of things that can be done to make your house comfortable to live in and always seem to be brand new.

Scratches

Superficial scratches are one of the most commonplace causes for drywall repairs. Homeowners with small children or people who move large furniture around are most likely to encounter this problem. Scratches may be as shallow as the paint layer or go on deeper to the paper layer of the sheet. This problem is remedied by having the damaged area covered with joint compound and having it sanded before getting a new paint job.

Surface bruises

This type of wall damage is something in between a scratch and a hole. Surface bruises are carved out parts of the wall that are deeper than superficial scratches but do not go all the way through the board. Unlike in repairing scratches, a fiber glass mesh is needed in combination with the joint compound to effectively repair the drywall. Instead of just one, two applications are necessary to even out the surface and make sure that it does not worsen into a hole. After drying, sanding and priming is done before it is painted.

Holes

Another common cause for drywall repairs would be the presence of holes. Smaller holes created by nails or other objects can be repaired in the same way as scratches. Medium-sized holes require the use of metal plates or aluminum plates to support the damaged area of the wall before it is smoothed over with a joint compound, sanded, primed, and painted.

Water damage

The worst type of damage would be that caused by water or flooding. The best way to repair this is to have the damaged boards cut out and have new ones reinstalled. Horizontal installation of drywall is commonly used for this type of repair because it is easier to make the wall even and avoid distortion.

Vinyl Flooring Practical, Durable And Affordable

How long does vinyl flooring last?

Are you thinking of installing vinyl in your home? Before you make your final selection, you may want to consider the longevity of what you will be installing. Every material has pros and cons, and what you select is often at the intersection of affordability, durability, and aesthetics.

Today’s vinyl flooring options can meet all three of those requirements, which is why its a popular choice. Vinyl plank flooring has grown in popularity because of it’s ability to look like the real thing, while giving you the affordability and durability you’ll love.How Long Does Vinyl Plank Flooring Last

The longevity of vinyl plank flooring depends on the thickness and the wear layer of the product you are purchasing. Some of the thicker vinyl floors on the market come with warranties for up to 25 years. If you are using a thin vinyl, you’ll most likely get a wear life of somewhere between 5 and 10 years with normal use.

Vinyl plank is designed to resemble hardwood, and it comes in strips in much the same fashion as a hardwood alternative. You can find this product in a number of looks and styles, each mimicking a specific type of wood. Because it is designed to imitate hardwood, you’ll find a version that matches your home’s decor.

Vinyl plank has many advantages over its hardwood counterparts.

Because many models are backed with a felt product, when installed it provides a softer floor with more give. That means less breakage when things are dropped, which is good news for plates and glasses in the kitchen.

Vinly floor is water resistant, making vinyl plank the perfect choice in kitchens and bathrooms. In fact, vinyl is better at sealing against water damage, so it’s especially durable in basement locations.

Vinyl plank can be installed directly on your subfloor, which makes the process quick, cost-effective, and easy to handle.

And because vinyl is one of the easiest surfaces to maintaince, it’s a wise choice in a busy household with lots of foot traffic.

Keep in mind that while vinyl will hold up for many years, it can be damaged quite easily. Avoid moving heavy furniture around, which can result in scuffs and gouges. If any particles are left beneath during installation, it can create bumps or warps in your floors. And keep in mind that vinyl does little to add to the resale value of your home.

Recycling Used Vinyl Plank Flooring

It is possible to recycle all forms of vinyl, including vinyl plank flooring. Vinyl has been diverted from landfills and trash sites since before the turn of the century, and post-industrial recycling helps to put even the cut-offs back into other finished vinyl products. With this in mind, it is comparatively easy to get your used vinyl plank flooring recycled.

Re-Using the Flooring

Most vinyl floor manufacturers agree that, if the floors were made in the last decade, then it is possible to reuse the floors as whole pieces, although a lot depends upon the glues used in the original vinyl. Tiles and shorter boards can be made from vinyl plank flooring, and it can also be used whole as carpet backing. Vinyl plank flooring can therefore be recycled if they are kept as whole as possible.

Recycling the Material

Vinyl plank boarding can often not be recycled whole, and may end up in a trash bin because of this. However, you can get in contact with recycling firms through a list available on the internet, find out if anyone wishes to strip the vinyl from the backing, and use that to recycle. If you want your vinyl plank flooring to be environmentally friendly, then it is best to install recycled planks at the start, rather than attempting to make them green at the end of their life.

Vinyl Flooring Pros and Cons

Vinyl flooring has been a popular flooring choice in America for many years, and it still accounts for around 15 percent of annual flooring expenditures in the country. When most people talk about vinyl flooring they’re usually thinking about sheet flooring. However, there are other forms of flooring made from vinyl, such as tiles and planks. Since they’re all are made from vinyl they share a number of common characteristics and have many of the same advantages and disadvantages.

Advantages

Affordability – Vinyl’s primary advantage is its affordability. While it can emulate high-end flooring in appearance, vinyl flooring is relatively inexpensive and can be installed for as little as $5 per square foot.

Wide Color Choice – All vinyl flooring is available in a wide range of colors, making it adaptable and easy to fit into almost any decor.

Quick and Easy Installation – Available in tiles and planks as well as sheets, it’s easy to install. The tiles usually come in 12-inch squares, so they’re easy to handle and both the tile and planks are often manufactured with “peel and stick” backings, meaning they’re easy for homeowners to put down themselves (saving money on professional installation).

Moisture Resistance – Vinyl flooring is totally waterproof, so it can be used virtually anywhere in the home including the main floor, upper floors and below grade. It works particularly well in bathrooms and kitchens, where water often ends up on the floor.

Easy Cleanup – Water simply beads on the surface, making it easy to mop up. Plus, regular sweeping and an occasional damp mopping are all that’s required to keep a vinyl floor clean and bright.

Durability – Most vinyl flooring has a wear layer (sometimes up to three) on top of the vinyl itself, so it’s resistant to normal traffic wear.

Comfort – Vinyl is a resilient flooring, meaning it’s soft texture has a little give when you walk on it, making it a good working floor you can stand on for hours.

Disadvantages

Petroleum Product – Vinyl is made from petroleum, so from an environmental perspective because it’s made from a non-renewable resource it’s a bad product.

No Resurfacing – While the wear layer is designed to protect the flooring, after a few years of traffic the surface will start to show scuffing and signs of wear. Unlike wood, the vinyl floor can’t have a new finish applied.

Color Fade – Vinyl can’t stand up to ultra violet rays so under prolonged exposure to sunlight the patterns and colors in a vinyl floor will start to fade.

Difficult or Impossible Repairs – While vinyl is durable, if it does get damaged it’s hard to patch. A vinyl tile or plank can be removed and a new one installed, but a sheet vinyl floor needs to be replaced.

Surface Irregularities – Over time some vinyl floors develop bumps or curls at the edges or along the seams.

Clean Vinyl Plank Flooring

One of the advantages of vinyl plank flooring is the ease of maintenance. Keeping the vinyl clean is very simple. With all the look of hardwood and none of the headaches, vinyl plank flooring is much less expensive and easier to install.

Step 1 – Sweep/Vacuum Floor

To remove dirt and dust from your vinyl plank flooring, vacuum or sweep it with a broom. This should be a daily chore to keep the finish shiny. Follow up with dry micro-static-fiber floor duster to catch remaining dust.

Step 2 – Clean Floor

Add 1 tbsp of ammonia (or liquid dish liquid) to 1 quart of water. Wash the floor using a clean rag or mop. Alternatively, you can use whichever self-cleaning (no rinse) floor cleaner is recommended by your floor’s manufacturer.

Step 3 – Rinse Floor

If you decide to use liquid dish soap, rinse residue with clear water. If you don’t rinse, the floor will be sticky.

Step 4 – Yearly Maintenance

The manufacturer of your floor might recommended that you apply a new coat of floor polish to keep your floor glossy and provide additional protection against wear. Please note that using a vacuum with a beater bar can damage vinyl planks, so you should not use it on your flooring. Additionally, avoid using abrasive cleaners and scrubbing pads, which can scratch the surface of the vinyl.

A Home Builder Common Sense Approach To Green Building

Things to Know About the Custom Home Building Process

Building a home to your specifications is an exciting experience, but you have to ensure you are well prepared for the project. You also need to learn about the custom home building process.

Don’t know anything about the building process? Well, worry not. In this piece, we are going to look at seven important things you should know about building a custom home.

Be Ready to Tackle One Thing at a Time

Building a custom home or remodeling a house to match your specifications can be an exhaustive experience, especially if you are a first-timer. Therefore, you want to be relaxed and ready to tackle one thing at a time. You should note that your custom home will only make you happy if your decisions were made intentionally and not on impulse.

You Should Be Realistic

Like most people, you want to live in a house where you can get everything you want, including recreation facilities. But let’s face it; unless you are very rich, some of the features you see in your dream home might not come true. You should, therefore, be realistic when coming up with your plan and budget. The best way to do this is to come up with a list of all the features that you want to see in your dream house.

Choose Your Team Wisely

If you want to succeed in building your custom home, you must be careful when choosing a custom builder. Make sure the custom builder you hire has the knowledge, skills, and experience required to give you the exceptional results you are looking for. The custom builder you choose should also come with a team that understands the process of constructing a custom home. Everyone who works for you should be licensed, bonded, and insured. This way, you can relax knowing that your project is in good hands and they will deliver on time.

What to Know Before Buying New Construction

Buying a new construction home is a very different process from purchasing a previously owned home. Here are a few things to keep in mind as you consider whether new construction is right for you.

Hire a Real Estate Agent

Some buyers don’t feel a real estate agent is necessary when building a new home. They think that because there is a sales agent on-site they don’t need to bring in anyone else, right? Wrong. This mistake could cost you – and we’re not just saying that so you hire a Realtor! That on-site person works for and represents the seller.

Have Your Earnest Money Deposit on New Construction Ready

When purchasing a home that has been previously owned, the earnest money on new construction is typically 1-2% of the sales price. When purchasing new construction, your earnest money deposit is usually 5% of the sales price. The builder typically mandates the amount as a part of their contract (see more on builder contracts below).

Be Prepared to Wait

Delivery can range – it could be immediate or more than a year. Make sure you understand the delivery timeframes and be prepared for these timeframes to be extended a bit. Almost every new construction project hits delays.

The Fine Print

Many builders use contracts that are much different from the area real estate board contracts used in a re-sale transactions. These contracts mostly protect the builder, not the buyer. So be sure you really read through the fine print. If you are buying from a smaller or relatively unknown builder in your area

Considerations for Building a Mountain Home

Finding the perfect lot is the first step towards making your dreams of mountain living come true. If you’re planning to build a custom home – especially in the mountains – there are many important factors to take into consideration when selecting your lot and designing your home. Depending on where you are from, some of these factors may be new to you. This blog is meant to give you a general idea of the most important factors to consider, but is not an exhaustive list or a substitute for a good real estate agent.

Location – How will you get there?

filled with beautiful mountain towns. If you are building a vacation home in the mountains, consider how you will get there. How close is the nearest airport? Are there convenient flights available from your home town? Distance can be deceiving in the mountains, and traffic jams are especially common in the winter months when roads become snow packed and icy.

Snow Removal and Road Maintenance

It is important to find out who is responsible for snow removal and road maintenance in your neighborhood. In many areas, the city or county will plow the roads, or the HOA might have a contract in place for snow removal. Find out which access roads will be plowed, and if your driveway is included. If you plan to build in a more remote area, it is important to be prepared for the fact that you may need to plow your own way out after a big snow storm.

Snow and Architecture

When building a home in the mountains, never underestimate the influence of snow. Site placement is one of the first decisions your architect will make, and the orientation of your home and the driveway should take snow into consideration. In an ideal world, they will be able to situate your driveway to be south facing, meaning the sun exposure will help melt the snow, keeping your driveway from becoming packed with ice. If the site does not allow this, you will want to consider a heated driveway.

Zoning and Setbacks

No matter where you plan to build, it is important to be familiar with the zoning and setbacks for your lot. If your goal is to build a duplex, make sure your property is zoned for this. In general, if the zoning allows for a duplex, you could still build a single-family home on the property, but not vice versa. Some neighborhoods also have protective covenants or design guidelines that must be considered. Setbacks – which are the minimum distance from the lot lines to the structure – should also be considered, but their impact varies depending on the size of your lot. On small lots the setbacks can dictate the size and placement of your home, however on larger lots they have much less impact. The most important thing is to make sure you can live with the rules before you purchase the property.

Home Builder Resources

Doing the research and accessing the information you need about building a home can get a little stressful, so we’ve put together this section as a hub for useful material and resources to make it a little easier for the new home builder. Here you’ll find a host of downloadable information and guides to help you make decisions and consider your options

From information about knocking down an existing home to finance guides, upgrade packages and details about the various government grants, this hub is a one-stop shop for new home builders

You’ll be delighted by the magic that our stunning Two Storey designs offer. No matter your lot size this wonderful range of homes will complete your lifestyle desires and fill you with excitement for your future.

range further enhances our new affordable range of contemporary homes, complete with everything you need, and nothing you don’t. These quality homes are designed to give you the extra space you need on modern compact blocks and elevate the way you live.

an affordable range of homes complete with everything you need, and nothing you don’t. These homes are the perfect blank canvas for you to start your new life in your new home and make a home that’s truly yours.

The Importance of Building Science

If you’ve made it to this blog, chances are you’ve heard a thing or two about building, or about its components:  energy efficiency, air quality, material sustainability or building durability. But have you heard about an umbrella term that encompasses many of these topics, the interdisciplinary study of building science?

What is building science?

Building science is simply applying what we know about physics and other sciences to buildings, with a focus on moisture and heat. As such, building science touches on concepts from material science:  the engineering discipline that studies the physical and chemical properties of materials (e.g. brick, plywood,insulation, drywall, anything buildings are made out of that might interact with moisture and heat in ways that may need to be considered), thermodynamics:  dealing with methods of heat transfer, phase changes, pressure dynamics, and mechanical engineering:  which gets into all the nitty-gritty of airflows and motors and equipment that generates heat, cools air, or produces or removes moisture, and even touches some on health and biology with respect to indoor air quality and mold growth (a natural consequence of moisture.) And it’s pretty helpful to mix that in with a dose of construction management:  the common and necessary techniques of construction, how jobs are sequenced, and the best places in the construction process to do what with what material.

Why is building science important?

Buildings use a lot of energy, and energy use has concerning environmental and economic impacts. The biggest component of energy use in most residential buildings is heating and cooling. Meanwhile, moisture in buildings can have huge impacts on the durability of building materials and on human health, and is a huge source of litigation in the building world. Moisture and heat are often tied together in today’s buildings, due to physics, and due to mechanical systems which can be a way to remove moisture, or can sometime fail to adequately do so.

Additionally, while some problems with buildings would become obvious very quickly: (e.g. if the structure isn’t engineered right, gravity will pull it down; or if the electrical isn’t done right, you might have a fire) the discipline of building science often focuses on more insidious problems that might take time to develop. Things like high energy use due to hidden holes and drafts in a building, or moisture that builds up over time due to defects in flashing.

So, what kind of science is happening these days with respect to buildings?

Studying the properties of materials, and common ways they might get layered in a typical building, is one of the biggest areas of ongoing research. There are so many product manufacturers out there making all kinds of different building products. For instance, sidings made from coal ash, composite wood, concrete, or a mix of all it; insulation made from plastic, recycled blue jeans, or spun volcanic rock fibers.

How A Reputable Office Movers Protects Your Vital Records

Specialist office movers

office movers are part of our Business Solutions division, offering a portfolio of services which helps thousands of businesses each year to optimise and design a new office environment, and relocate their staff and infrastructure to new premises.

If you utilise moving and storage services in more than one area of your organisation, by choosing multiple services

office removals services are delivered by professional experts, national branch experts and international resources. Customer satisfaction is highest priority and every aspect of accredited service is underpinned by passionate people, proven processes and innovative technology.

COVID-19 Guidance for Customers

Due to the unprecedented situation with regard to the spread of the Covid-19 virus, the removal industry has had to review its operational procedures in order to protect both customers and employees from the risk of infection

removal teams have had instruction on how to maximise protection while working within the close quarters of your home to ensure your safety. This includes safe use of PPE, frequent washing of hands and sanitising vehicles, and the washing of uniforms daily at high temperatures.

Office Move Team

Office moves are monumental, but if you start the process the moment you think you’re changing spaces, they get a lot easier. This is second office move, and while may be experts in creating workspaces, still face many of the same obstacles clients do. So, thought document experience.

started with the listening phase and been listening to internal feedback for a while now – after all, the first step to creating a really great brief is fully understanding your client.

Q: Who’s been involved in the office move process so far?

A: “I think a better question would be ‘who hasn’t been involved in the office move?’ have put a process in place to make sure that everybody who wants to add value to the process gets to have a say, whether it’s through a diary room, through a formal one-to-one interview or through workshops. So, I think pretty much everyone – it’s an all-encompassing process.”

Q: What has been the most challenging aspect to date?

A: “So, I think the overall design feel of the office, who holds that? Because Creative Director, is running the design but he doesn’t want to be the designer, because got a whole host of very talented young designers and he wants them to all add value. Working out how that’s going to be pulled together, that’s the most challenging conversation I think I’ve heard so far.”

Q: Why is it important for businesses to invest in their workspace?

A: “Because it’s an opportunity to establish the environment that accurately portrays the correct operational way of working. So, when you’re trying to grow organisations or change the nature of the way an organisation operates – and for, it’s a lot about growth and reinvigoration – your new office won’t do that on its own, but it will be one of the catalysts to let that growth happen. I think that’s a real important part of it.”

Planning an office move

This will help in ensuring you can get back up and running again smoothly.

Username of person moving

UG number of PC being moved

Mac Address of PC

IP address of PC

Machine Name of PC

Current room number and Building

Current socket number PC is plugged into

New room number and Building

New socket number PC to be plugged into

Telephone number

Socket number telephone is plugged into

New socket number telephone is to be moved to

Date of move

Things to consider

You will need to contact Facilities Management to arrange for office furniture and IT equipment to be moved. Visit your new office beforehand to visually inspect the space you will be moving into. You may find that there are not enough network or phone sockets to meet your needs. If this is the case, contact the IT Service Desk to discuss your requirements and obtain a quote.

To find the socket numbers

Look at the number above the right hand side of the network socket your PC is connected to. The network socket will be on the wall or inside a panel on the floor.

To find the MAC and IP address of your PC

Click on the start button

Select run

Type cmd and then press return, you will then see a black screen.

Type ipconfig/all

You will find IP address and the physical(MAC) address in this list of information.

To find the machine name of your PC

Right-click on the My Computer icon (Looks like a computer, usually on the top-left of the desktop)

Select properties

Select the tab that will be called either network identification or machine name

The machine name can be found under Full computer name

Things to Consider when Moving Your Office

Is an office move on your company’s horizon? Whether yours is a small, midsize, or large business, there are several things you can do to ensure a hassle-free moving experience with minimal downtime.

Give Everyone a Job to Do

Creating a moving checklist is an excellent way to get everyone involved. Your checklist should cover everything required before moving and after moving into your new office. Depending on the size of your move, you might want to create a “move committee” charged with executing your moving plan, crossing off tasks as they’re completed, adding new tasks when necessary, and keeping everyone busy.

Alert Your Current Vendors

Well before your actual moving day, make sure to contact your current vendors regarding your move. If you’re moving to a building that’s local, you may only need to give your vendors a change of address. But if your new office is in a different state, you’ll probably need to cancel services with your existing vendors and contract with vendors in your new city.

Post a Schedule

Whenever a business contracts with for office relocation services, explain the necessity of creating a schedule with all relevant target dates, and posting it in a high-traffic location so everyone is aware of what’s happening. The entire office should of course be aware of the final move-out date and the expected date of arrival in the new office. Add other relevant dates pertaining to your office space, i.e. “IT backup day”, “cleaning day”, etc.

Hire Movers

No matter how big or small your business, it’s a virtual certainty that you’ll require the expertise of a full-service commercial moving company. Assign one or two co-workers to determine a moving budget, create a list of candidates, interview each one, conduct the necessary background checks and reference confirmations, and make the hire.

key traits of reliable office movers

those aren’t so easy to come by. That’s why you need to know the general rules and qualities to look for when searching for your moving team. And all of these key traits of reliable office movers should be checked off your list before sealing the deal with your movers.

Depending on your moving needs, there are many different things you could look for in movers. For example, you could look for a team that provides commercial junk removal services or you could need a team that deals with labor services only

You need to know that the team you have hired is a trustworthy one. After all, how else are you supposed to entrust them with all of your office possessions? Look up the previous experience of other people and decide based on their comments whether they are a good and trustworthy option.

Reputability

Have you received a couple of word-of-mouth recommendations for the movers in questions? Have you heard their name come up once or twice in previous conversations? If you have, then you can rest assured you have found a reputable moving company, and those companies usually live up to their reputation.

Affordability

The cheapest moving company definitely doesn’t equal the best moving company. But neither does the most expensive one. Good movers that care about you won’t impose steep prices. So if you stumble upon a company with reasonable pricing options, you have most likely found good office movers.

Event Planner, Wedding Coordinators

How to Plan an Event

Looking to plan your first event? Maybe you’ve been planning events for a while but want to ensure you’re using the best possible framework. Understanding the key components, ensuring you have an event plan and creating lists to help you check off all of those last minute details is a system event planners use to ensure success.

In this guide we’ll walk you through what event planning is, what it involves and how to write an event plan, step-by-step, with a checklist to help you along the way.

What is event planning?

Event planning is the organisation of all of the activities that surround an event. This could be a party, a festival, a conference or a tradeshow. Planning an event takes lots of work and key organisational skills. Event planners will often work on everything from catering, to entertainment, booking presenters and managing exhibitors. The event planning process ensures that all of these areas are covered, that the event remains within budget and that it is delivered on time and fulfils the event objective(s).

Key components of event planning

The key areas an event planner will manage include:

  • Event preparation – writing an event plan, documenting budgets and timelines and researching suppliers like caterers or staff members.
  • Event promotion – all of the aspects that help to sell the event, raise awareness and increase the number of attendees.
  • On-site event management – making sure the big day (or days) goes without a hitch and that everyone is where they need to be. Putting out any onsite fires!
  • Post-event review – organising debriefs, data collection and analysis and reviewing these against the original event aims and figures.

Best Practices When Creating an Event Plan

  • Determine the objective. Determine what the client or sponsoring organization hopes to achieve with the event.
  • Establish a budget. A budget should include true estimates of key elements of the event. Provide an outline of the budget in the event plan. Include travel and accommodation costs for the site scouting team, speakers, presenters, and special guests from out of town.
  • Organize a team. A successful event plan requires a concerted team effort. Among your event project team you may choose to identify an event manager or event chair as well as chairpersons for subcommittees. Subcommittees may include venue selection, speakers, entertainment, sponsors, volunteer management, and marketing.
  • Set a date. If it’s a reoccurring event, the date may already be established. If this is a new event, there are a few things to consider before finalizing the date:
  • Allow enough time to prepare. Larger events may require four to six months, perhaps even longer, to execute an event plan. Obviously, the selection of the lead time is dependent on the size, nature, and timing of your event.
    • Be mindful of national and religious holidays.
    • Check availability of key participants such as honored or VIP guests, speakers, presenters, entertainment, etc.
  • Create a plan. The event plan must encompass all aspects of the event, including:
  • Venue, logistics, catering
    • Presenters, key note speakers
    • Entertainment and activities
    • Marketing efforts
    • Registration logistics
    • Sponsorship or partnership management
    • Volunteer management

Event safety plan

When it comes to keeping your event attendees, staff members and presenters safe, there are many elements to consider. The government’s health and safety for events guidelines can help to ensure you think about the different elements such as:

  • Reducing risk
  • Creating information for employees or attendees
  • Organising contractor health and safety
  • First aid, toilets and wash facilities
  • Parking
  • Waste removal
  • Food health and safety

Event planning checklist

Use this checklist to ensure you have thought about all of the key areas relating to your event. Have you:

  • Determined the event goals and objectives
  • Produced a written event plan
  • Defined the event audience
  • Conducted market research
  • Finalised the event budget
  • Decided on an event name
  • Booked an event venue
  • Created a marketing plan and timeline
  • Selected your vendors
  • Secured your event sponsorship
  • Determined a registration system
  • Launched an event website
  • Launched the event marketing campaign
  • Scheduled an email marketing campaign
  • Booked speakers and presenters
  • Organised insurance and health and safety compliance
  • Organised catering
  • Organised audio visual, lighting and staging
  • Booked entertainment
  • Hired event staff
  • Determined a lead capture system
  • Ordered event signage
  • Involved local or industry press
  • Reviewed and analysed event success

Getting Started on the Event Proposal

Each proposal should be written with the client in mind. Event planning is a service business, and that service, personal touch, and creative approach are what make an event successful and memorable, two characteristics that go a long way in generating new customers for your business. Proposals should be well written and thoroughly researched, providing the necessary details so that the client can envision what you have in mind.

  • Introduce yourself and the project. Begin with a brief introduction to you and your event planning business. Include specifics such as how long you have been in business and your professional background. Some planners put this section at the end, much like a book author’s biography on a dust jacket or back cover.
  • Write an attractive event description. Summarize the actual event, including the details discussed during your meetings, such as the goal of the event, general time frame, number of guests, and possible venues. If you are not a skilled writer, find or hire someone skilled with words to give this section as much appeal as possible.
  • List all services provided. This section is particularly important. The client needs to know specifically what services you will provide for this event. A checklist with bullet points clearly shows the different services that are included. This approach works well for smaller functions such as bridal showers or celebratory dinners and is easy for the client to see what you will do and any vendors you will use. For larger events with multiple functions, such as a cocktail hour or luncheon, you may want to create sections for each aspect of the event and then list the specific services provided for each one.
  • Show your previous work. If you have planned similar events in the past, include photos of these events to showcase your work. Visual representations can help the client see what you can do, and are a great assurance to you that your style matches their vision. Having things to compare against can really help streamline the event once it comes time to break ground.
  • Incorporate monetary information throughout. While the client may be reading your proposal and taking in all the details and images of the event you envision, this mindset usually shifts gears when it comes to the section that talks about money. You don’t want the process coming to an abrupt stop, so avoid sudden changes in the language or tone to all business and facts. Title a section “Proposed Costs” and continue to guide the client through the aspects of this event by carefully articulating the costs, while peppering prices throughout the proposal. Help your client see your proposal as a series of steps, each with different services and related costs. Provide a detailed summary that lists the price for each item and its purpose so that the client can envision the event and understand the related cost.

Introduction To Personal Injury Lawyer

What does personal injury lawyers do?

How a Personal Injury Attorney Can Help You

When you’re seriously injured in an accident, you need a personal injury lawyer to handle your claim. But, what exactly does a personal injury lawyer do?

Most people know that if you are hurt in a car accident, a personal injury lawyer can help you get compensation for your injuries. However, most personal injury lawyers can help with more than vehicle accident cases. The attorneys at the Dolman Law Group and Sibley Dolman cover several practice areas that fall under personal injury law. If another person or a company injured you, contact our firms for a free consultation and case evaluation.

Whether you’re hurt in a fall or an auto accident, by a defective product or due to some other occurrence, you need to concentrate on your recovery. As you focus on emergency medical treatment, doctors, nurses, medications, surgical interventions, and therapeutic treatments, your attorney focuses on protecting your legal rights. He establishes a barrier between you and all of the people who would disrupt your peace of mind.

  • As your medical bills begin to pile up, hospital administrators will want to know how you plan to pay them.
  • If you were involved in an auto accident, the investigating police officer will want answers.
  • Your insurance company will need your statement. They’ll want to determine if they owe you PIP benefits and if they owe the other driver’s damages
  • The other driver’s insurance company will need to know your version so they can figure out if they can walk away without paying you anything.
  • If you fell on someone’s property, the liability insurance company will want to know what happened.
  • If you were injured on the job, the HR department and your boss will also have a few questions to ask.

Client relations

Before accepting a new case, a personal injury lawyer typically interviews a prospective client and evaluates the client’s case to determine the basic facts and potential legal claims that might be made, identifies possible defendants, and evaluates the strength of the case. A lawyer may decline to accept a case if the lawyer believes that the legal claims will not succeed in court, if the cost of litigation is expected to exceed the amount that can reasonably be recovered from the defendants as compensation for the client’s injury.

Compensation

Lawyer fees may be charged in a number of ways, including contingency fees, hourly rates, and flat fees. In many countries, personal injury lawyers work primarily on a contingency fee basis, sometimes called an if-come fee, through which the lawyer receives a percentage of a client’s recovery as a fee, but does not recover a fee if the claim is not successful.

In some jurisdictions, or by virtue of the retainer agreement between an attorney and client, the amount of the legal fee may vary depending upon whether a case settles before a lawsuit is filed, after a lawsuit is filed but before trial, or if the case goes to trial.[8] For example, a retainer agreement might provide that a lawyer will receive a 33 and 1/3% contingency fee if a case settles before a lawsuit is filed, a 40% contingency fee if the case settles after the lawsuit is filed, or up to 45% if the lawsuit goes to trial.

Due to the high cost of litigation, personal injury lawyers are rarely retained to work based on an hourly fee. However, defense attorneys who are hired to contest personal injury claims are often paid on an hourly basis.

The Personal Injury Litigation Process

A personal injury lawsuit starts with the filing of the complaint, a legal document listing your legal arguments, the facts in support of those legal arguments, and what you demand in relief.

After you file the complaint and serve it on the defendant (the person you’re suing), the defendant will file a response to your complaint (the “answer”).

Next, “discovery” begins. This is the stage of litigation where the two sides exchange information that might serve as evidence during trial. In most personal injury cases, discovery will consist of depositions, requests for documents, and interrogatories, and the process can take months to complete.

After discovery, the trial is set. Your attorney may file a variety of pre-trial motions (to try to keep the defendant from using a piece of evidence during trial, for example). It’s very rare for a personal injury lawsuit to reach the trial phase. Settlement is possible at any point during this process, including right up to (or even during) trial.

Your personal injury lawyer will take care of all aspects of the litigation phase and will keep you updated on your case’s progress.The Personal Injury Litigation Process

A personal injury lawsuit starts with the filing of the complaint, a legal document listing your legal arguments, the facts in support of those legal arguments, and what you demand in relief.

After you file the complaint and serve it on the defendant (the person you’re suing), the defendant will file a response to your complaint (the “answer”).

Next, “discovery” begins. This is the stage of litigation where the two sides exchange information that might serve as evidence during trial. In most personal injury cases, discovery will consist of depositions, requests for documents, and interrogatories, and the process can take months to complete.

After discovery, the trial is set. Your attorney may file a variety of pre-trial motions (to try to keep the defendant from using a piece of evidence during trial, for example). It’s very rare for a personal injury lawsuit to reach the trial phase. Settlement is possible at any point during this process, including right up to (or even during) trial.

Your personal injury lawyer will take care of all aspects of the litigation phase and will keep you updated on your case’s progress.

Points to Keep in Mind After Hiring a Lawyer

Your attorney probably can’t respond immediately to your telephone calls or emails. Lawyers are ethically bound to respond to clients within a reasonable amount of time, but they have other cases to work on, depositions to prepare for, and court hearings to attend.

One thing your lawyer should never do is keep you in the dark about what’s going on in your case, especially if the other side makes a settlement offer. Unless you’ve given your permission, your lawyer cannot accept or reject a settlement offer without running it by you first.

Be careful discussing your case with anyone other than your lawyer or a representative from your lawyer’s office. If you get a call from an insurance adjuster or someone you’re not familiar with, don’t talk to them about your case. If they have legitimate questions or concerns about your case, you can refer them to your attorney. On a related note, unless your attorney advises you otherwise, do not sign any document relating to your case, and do not change doctors.

Keep your lawyer updated. For instance, if you finish your medical treatment, tell your attorney. If the defendant or someone working on behalf of the defendant tries to contact you, tell your attorney. If you receive additional medical bills or other documents that substantiate your damages claim, tell your attorney and send them copies of relevant documents.

If you’re having money struggles as a result of your personal injury, tell your attorney. They can suggest avenues of financial support and give you advice on how to deal with creditors.

What types of cases do personal injury lawyers handle?

Personal injury lawyers handle several types of negligence cases that involve car accidents, truck accidents, aviation accidents, medical malpractice, legal malpractice, child daycare negligence, wrongful death cases, and other types of negligence cases. Negligence occurs when someone fails to use reasonable care to avoid causing injury or loss to another person. In other words, negligence occurs when one person carelessly injures another person.

Posted inLegal